Macsym Tecnologia Eletrônica

BeeHive204

BeeHive204 Ampliar

BeeHive204

  • Marca: ELNEC
  • Código: 9PE600053
  • Preço: Sob consulta
  • Peso: 2,000

BeeHive204

BeeHive204
(ord.no. 60-0053)
 
Extremely fast universal 4x 48-pindrive concurrent production programmer (multiprogramming system).

Short description: 71 405 supported devices from 290 manufacturers by 2.87 version of SW (1. Mar. 2012)
 four independent universal programming modules (BeeProg2 based) in one unit
two BeeHive204 multiprogrammers can be attached to one PC to better utilize programming workplace
extremely fast programming, one of the fastest programmers in this category. Programs 64Mbit NOR Flash memory less than 9 seconds and 1Gbit NAND Flash less than 70 sec.
powerful independent pin driver circuit for each and every pin of the programmer
in-circuit programming capability through ISP connector
Very low voltage support for latest Flash memory chips
ESD protection on each pin of the sockets
USB (up to 480 Mbit/s) interface to PC
comfortable and easy to use control program, Windows 2000/XP/2003/XPx64/Vista/7 compatible
unique quick reaction to customer's needs - software update can be ready within a day from request by OnDemand software
approved by CE laboratory to meet CE requirements
made in Slovakia
warranty - 3 years

GENERAL
 BeeHive204 programmer is practically identical with the BeeHive4+ programmer, difference is "only" much higher programming speed (20-70%) of high-capacity memories.
BeeHive204 is extremely fast universal 4x 48-pindrive concurrent multiprogramming system designed for high volume production programming with minimal operator effort. The chips are programmed at near theoretical maximum programming speed.
BeeHive204 consists of four independent isolated universal programming modules, based on the BeeProg2 programmer hardware. Therefore the sockets can run asynchronously (concurrent programming mode). Each programming module starts programming at the moment the chip is detected to be inserted in the socket properly - independently on the status of other programming modules. It result, three programming modules works while you replace the programmed chip at the fourth.
Modular construction of hardware - the programming modules works independently - allows for continuing operation when a part of the circuit becomes inoperable. It also makes service quick and easy.
Hands-free operation: asynchronous and concurrent operation allows a chip to begin programming immediately upon insertion of a chip. The operator merely removes the finished chip and inserts a new chip. Operator training is therefore minimized.
Supports all kinds of types and silicon technologies of today and tomorrow programmable devices without family-specific module. You can be sure the next devices support require the software update and (if necessary) simple package convertor (programming adapter), therefore the ownership cost are minimized.
Using built-in in-circuit serial programming (ISP) connector, the programmer is able to program ISP capable chips in circuit.
Provides very competitive price coupled with excellent hardware design for reliable programming. Probably best "value for money"programmer in this class.
Very fast programming due to high-speed FPGA driven hardware and execution of time-critical routines inside of the programmer. At least fast than competitors in this category, for many chips much faster than most competitors. As a result, when used in production this programmer waits for an operator, and not the other way round.
BeeHive204 interfaces with the IBM PC compatible, portable or desktop personal computers through USB (2.0) port.
Banana jack for ESD wrist straps connection to easy-to-implement the ESD protection control.
 

HARDWARE (valid for each programming module)
 FPGA based totally reconfigurable 48 powerful TTL pindrivers provide H/L/pull_up/pull_down and read capability for each pin of socket. Advanced pindrivers incorporate high-quality high-speed circuitry to deliver signals without overshoot or ground bounce for all supported devices. Pin drivers operate down to 1.8V so you'll be ready to program the full range of today's advanced low-voltage devices.
Each programming module performs device insertion test (wrong or backward position) and contact check (poor contact pin-to-socket) before it programs each device. These capabilities, supported by overcurrent protection and signature-byte check help prevent chip damage due to operator error.
The selftest capability allow to run diagnostic part of software to thoroughly check the health of the each programming module.
Built-in protection circuits eliminate damage of the programming module and/or programmed device due to environment or operator failure. All ZIF socket pins inputs and all pins of ISP conncetor of BeeHive204 programmer are protected against ESD up to 15kV.
BeeHive204 programmer performs programming verification at the marginal level of supply voltage, which, obviously, improves programming yield, and guarantees long data retention.
Various Programming Adapters (Socket Converters) are available to handle device in PLCC, SOIC, PSOP, SSOP, TSOP, TSSOP, TQFP, QFN (MLF), SDIP, BGA and other packages.
 

SOFTWARE (production mode control)
 This part of the software is focused to the easy monitoring of high-volume production operations.
Operator-friendly control software combines many powerful functions with ease of use. Graphic user interface provide overview of all important activities result without burden of operator with non-important details.

There is used a project file to control the BeeHive204 multiprogramming system. Project file contains user data, chip programming setup information, chip configuration data, auto programming command sequence, etc. Therefore the operator error is minimized, because the project file is normally created and proofed by engineering and then given to the operator. The optional protected mode can be set for project file to avoid a unwanted changes of the project file.

Each chip may be programmed with different data such as serial number, configuration and calibration information.
 

SOFTWARE (programming modules driver, engineering mode control)
 This part of the software is focused to the quick and easy preparation of the project file for usage in the production mode control software.
Each programming module is driven by an easy-to-use control program with pull-down menu, hot keys and on-line help. Selecting of device is performed by its class, by manufacturer or simply by typing a fragment of vendor name and/or part number. It is the same years-proven software, as is used for all other Elnec single-site programmers.

Standard device-related commands (read, blank check, program, verify, erase) are boosted by some test functions (insertion test, connection check, signature-byte check), and some special functions (autoincrement, production mode - start immediately after insertion of chip into socket).
All known data formats are supported. Automatic file format detection and conversion during loading of file. There is possible to use Jam files (JEDEC standard JESD-71) and VME files
The rich-featured auto-increment function enables one to assign individual serial numbers to each programmed device - or simply increments a serial number, or the function enables one to read serial numbers or any programmed device identification signatures from a file.
The software also provide a many information about programmed device. As a special, the drawing of all available packages are provided. The software provide also explanation of chip labelling (the meaning of prefixes and suffixes at the chips) for each supported chip.
 

CARE FOR THE CUSTOMERS
 New Device Request (AlgOR Service)
It is important to remember, that a support of most of the new devices requires only a software update, because the BeeHive204 is based on the truly universal (BeeProg2) programmer. With our prompt service you often can have a new device added to the list of supported devices within hours! See AlgOR (Algorithm On Request) service and OnDemand software for details.
This service is almost in all cases free. Please note that we can ask customer to share the cost if development cost is too high.

Free life-time software updates
Most current version of Elnec programmers software with support of newly added devices is available for free here.

Free Technical support
Elnec provide customers technical support (WebForm/e-mail based) available usually within few hours, at the latest next working day.

Keep-Current service
Keep-Current service means, that ELNEC ships the latest version of programmer software and updated user documentation (Keep-Current package) to customer . The Keep-Current service is your hassle-free guarantee that you achieving the highest quality programming on ELNEC programmers, at minimal cost.

Prompt delivery
Combination of extensive stock, flexible manufacturing and shipping of Elnec products by world class carriers (like DHL) warrants customers very fast and secure delivery of ordered Elnec products. Products ordered before 10 a.m. (CET) will be dispatched the same working day (if products are in stock and the payment is done by Online payment (CardPay, PayPal).

Warranty
Advanced design of the BeeHive204 production programmer, including protective circuits, original brand components, careful manufacturing and burning-in allow us to provide a three-year warranty on parts and workmanship of the programmer (limited 25 000-cycle warranty on ZIF sockets).
Elnec provides free shipping of programmer repaired under warranty back to customer world wide. Warranty is valid from the date of purchase.
Preferential handling of repair requests ensures registration of the product that should be done within 60 days from the date of purchase here.


Specification (BeeHive204 multiprogramming system)
 4x universal programming module (4x 48-pin DIL ZIF sockets)
operation result LEDs, LED power
USB 2.0 high-speed compatible port
line power input 100-240VAC/60W max.
protection against surge and ESD on power supply input
banana jack for ESD wrist straps connection
banana jack for connection to ground


Specification (valid for each programming module)
 
HARDWARE

Base unit, DACs
 USB 2.0 high-speed compatible port, up to 480 Mbit/s transfer rate
on-board intelligence: powerful microprocessor and FPGA based state machine
three D/A converters for VCCP, VPP1, and VPP2, controllable rise and fall time
VCCP range 0..8V/1A
VPP1, VPP2 range 0..26V/1A
autocalibration
selftest capability

ZIF sockets, pindriver
 48-pin DIL ZIF (Zero Insertion Force) socket accepts both 300/600 mil devices up to 48-pin
pindrivers: 48 universal
VCCP/VPP1/VPP2 can be connected to each pin
perfect ground for each pin
FPGA based TTL driver provides H, L, CLK, pull-up, pull-down on all pindriver pins
analog pindriver output level selectable from 1.8 V up to 26V
current limitation, overcurrent shutdown, power failure shutdown
ESD protection on each pin of socket (IEC1000-4-2: 15kV air, 8kV contact)
continuity test: each pin is tested before every programming operation

ISP connector
 20-pin male type with missinsertion lock
6 TTL pindrivers, provides H, L, CLK, pull-up, pull-down; level H selectable from 1.8V up to 5V to handle all (low-voltage including) devices.
1x VCCP voltage (range 2V..7V/100mA), can be applied to two pins
programmed chip voltage (VCCP) with both source/sink capability and voltage sense
1x VPP voltage (range 2V..25V/50mA), can be applied to six pins
target system supply voltage (range 2V..6V/250mA)
ESD protection on each pin of ISP connector (IEC1000-4-2: 15kV air, 8kV contact)
 two output signals, which indicate state of work result = LED OK and LED Error (active level: min 1.8V)
input signal, switch YES! equivalent (active level: max 0.8V)


DEVICE SUPPORT

Programmer, in ZIF socket
 EPROM: NMOS/CMOS, 2708*, 27xxx and 27Cxxx series, with 8/16 bit data width, full support for LV series
EEPROM: NMOS/CMOS, 28xxx, 28Cxxx, 27EExxx series, with 8/16 bit data width
Flash EPROM: 28Fxxx, 29Cxxx, 29Fxxx, 29BVxxx, 29LVxxx, 29Wxxx, 49Fxxx series, Samsung's K8Fxxxx, K8Cxxxx, K8Sxxxx, K8Pxxxx series, from 256Kbit to 1Gbit, with 8/16 bit data width, full support for LV series
NAND FLASH: Samsung K9xxx, Hynix HY27xxx, Toshiba TC58xxx, Micron MT29Fxxx, Spansion S30Mxxx, Numonyx (ex STM) NANDxxx
LBA-NAND: Toshiba THGVNxxx
mDOC H3: SanDisk (ex M-Systems) SDED5xxx, SDED7xxx, MD2533xxx, MD2534xxx, Hynix HY23xxx
Multi-chip devices: NAND+RAM, NOR+RAM, NOR+NOR+RAM, NAND+NOR+RAM
FRAM: Ramtron
MRAM: Everspin MRxxxxx8x
NV RAM: Dallas DSxxx, SGS/Inmos MKxxx, SIMTEK STKxxx, XICOR 2xxx, ZMD U63x series
PROM: AMD, Harris, National, Philips/Signetics, Tesla, TI
Serial E(E)PROM: Serial E(E)PROM: 11LCxxx, 24Cxxx, 24Fxxx, 25Cxxx, 59Cxxx, 85xxx, 93Cxxx, NVM3060, MDAxxx series, full support for LV series, AT88SCxxx
Serial Flash: standard SPI (25Pxxx, 25Fxxx, 25Lxxx, 25Bxxx, 25Txxx,25Sxxx, 25Vxxx, 25Uxxx, 25Wxxx, 45PExx), high performance Dual I/O SPI (25Dxxx, 25PXxxx), high performance Quad SPI (25Qxxx, 26Vxxx), DataFlash (AT45Dxxx, AT26Dxxx)
Configuration (EE)PROM: XCFxxx, XC17xxxx, XC18Vxxx, EPCxxx, EPCSxxx, AT17xxx, AT18Fxxx, 37LVxx
1-Wire E(E)PROM: DS1xxx, DS2xxx
PLD Altera: MAX 3000A, MAX 7000A, MAX 7000B, MAX 7000S, MAX7000AE, MAX II/G/Z
PLD Lattice: ispGAL22V10x, ispLSI1xxx, ispLSI1xxxEA, ispLSI2xxx, ispLSI2xxxA, ispLSI2xxxE, ispLSI2xxxV, ispLSI2xxxVE, ispLSI2xxxVL, LC4xxxB/C/V/ZC/ZE, M4-xx/xx, M4A3-xx/xx, M4A5-xx/xx, M4LV-xx/xx, ispCLOCK, Power Manager/II, ProcessorPM
PLD: Xilinx: XC9500, XC9500XL, XC9500XV, CoolRunner XPLA3, CoolRunner-II
other PLD: SPLD/CPLD series: AMI, Atmel, AMD-Vantis, Gould, Cypress, ICT, Lattice, NS, Philips, STM, VLSI, TI
FPGA: Actel: ProASIC3, IGLOO, Fusion
FPGA: Lattice: MachXO, LatticeXP, ispXPGA
FPGA: Xilinx: Spartan-3AN
Clocks: TI(TMS), Cypress
Special chips: Atmel Tire Pressure Monitoring ATA6285N, ATA6286N, PWM controllers: Zilker Labs, Analog Devices, Gamma buffers: TI, Maxim ...
Microcontrollers 48 series: 87x41, 87x42, 87x48, 87x49, 87x50 series
Microcontrollers 51 series: 87xx, 87Cxxx, 87LVxx, 89Cxxx, 89Sxxx, 89Fxxx, 89LVxxx, 89LSxxx, 89LPxxx, 89Exxx, 89Lxxx, all manufacturers, Philips LPC series
Microcontrollers Intel 196 series: 87C196 KB/KC/KD/KT/KR/...
Microcontrollers Atmel ARM. ARM7: AT91SAM7Sxx, AT91SAM7Lxx, AT91SAM7Xxx, AT91SAM7XCxx, AT91SAM7SExx series; ARM9: AT91SAM9xxx series; ARM Cortex-M3: AT91SAM3Uxxx series
Microcontrollers Atmel AVR 8bit/16bit: AT90Sxxxx, AT90pwm, AT90can, AT90usb, ATtiny, ATmega, ATxmega series
Microcontrollers Atmel AVR32: AT32UC3xxxx
Microcontrollers Chipcon (TI): CC11xx, CC24xx, CC25xx series
Microcontrollers Coreriver: Atom 1.0, MiDAS1.0, 1.1, 2.0, 2.1, 2.2, 3.0 series
Microcontrollers Cypress: CY7Cxxxxx, CY8Cxxxxx
Microcontrollers ELAN: EM78Pxxx
Microcontrollers Infineon(Siemens): XC800, C500, XC166, C166 series
Microcontrollers MDT 1xxx and 2xxx series
Microcontrollers Microchip PICmicro: PIC10xxx, PIC12xxx, PIC16xxx, PIC17Cxxx, PIC18xxx, PIC24xxx, dsPIC, PIC32xxx series
Microcontrollers Motorola/Freescale: HC05, HC08, HC11, HC12, HCS08, RS08, S12, S12X, MC56F, MCF51, MCF52 series
Microcontrollers Myson MTV2xx, 3xx, 4xx, 5xx, CS89xx series
Microcontrollers National: COP8xxx series
Microcontrollers NEC: uPD70Fxxx, uPD78Fxxx series
Microcontrollers Novatek: NT68xxx series
Microcontrollers Nuvoton (Winbond): N79xxx, W77xxx, W78xxx, W79xxx, W83xxx series
Microcontrollers NXP ARM Cortex-M3: LPC13xx, LPC17xx series
Microcontrollers Philips (NXP) UOC series: UOCIII, UOC-TOP, UOC-Fighter series
Microcontrollers Philips (NXP) ARM7: LPC2xxx, PCD807xx, SAF7780xxx series
Microcontrollers Scenix (Ubicom): SXxxx series
Microcontrollers Renesas: R8C/Tiny series
Microcontrollers SGS-Thomson: ST6xx, ST7xx, ST10xx, STR7xx series
Microcontrollers SyncMOS: SM59xxx, SM73xxx, SM79xxx, SM89xxx series
Microcontrollers & Programmable System Memory STMicroelectronics: uPSD, PSD series
Microcontrollers STM: ST6xx, ST7xx, ST10xx, STR7xx, STR9xx, STM32Fxx, STM8A/S/L series
Microcontrollers Silicon Laboratories(Cygnal): C8051 series
Microcontrollers Texas Instruments: MSP430, MSC12xx series, TMS320F series
Microcontrollers Texas Instruments (ex Luminary Micro): LM3Sxxx, LM3Sxxxx series
 Microcontrollers ZILOG: Z86/Z89xxx and Z8Fxxxx, Z8FMCxxxxx, Z16Fxxxx, ZGP323xxxxxx, ZLF645xxxxxxx, ZLP12840xxxxx, ZLP323xxxxxxx series
Microcontrollers other: EM Microelectronic, Fujitsu, Goal Semiconductor, Hitachi, Holtek, Novatek, Macronix, Princeton, Winbond, Samsung, Toshiba, Mitsubishi, Realtek, M-Square, ASP, Coreriver, Gencore, EXODUS Microelectronic, Megawin, Syntek, Topro, TinyARM, VersaChips, SunplusIT, Nordic, M-Square, QIXIN, Signetic, Tekmos, Weltrend, Amic, Cyrod Technologies, Ember, Ramtron, Nordic Semiconductor, Samsung ...
 
Programmer, through ISP connector
 Serial E(E)PROM: IIC series, MW series, SPI series, KEELOQ series, PLD configuration memories, UNI/O series
1-Wire E(E)PROM: DS1xxx, DS2xxx
Serial Flash: standard SPI (25xxx), DataFlash (AT45Dxxx, AT26Dxxx)
Microcontrollers Atmel: AT89Sxxx, AT90pwm, AT90can, AT90usb, AT90Sxxxx, ATtiny, ATmega, ATxmega, AT89LSxxx, AT89LPxxx
Microcontrollers Atmel AVR32: AT32UC3xxxx
Microcontrollers Chipcon (TI): CC11xx, CC24xx, CC25xx series
Microcontrollers Cypress: CY8C2xxxx
Microcontrollers Elan: EM78Pxxx, EM6xxx series
Microcontrollers EM Microelectronic: 4 and 8 bit series
Microcontrollers Microchip PICmicro: PIC10xxx, PIC12xxx, PIC16xxx, PIC17xxx, PIC18xxx, PIC24xxx, dsPIC, PIC32xxx series
Microcontrollers Mitsubishi: M16C
Microcontrollers Motorola/Freescale: HC08 (both 5-wire, All-wire), HC11, HC12, HCS08, S12, S12X, MC56F, MCF52 series
Microcontrollers Nordic Semiconductor: nRF24xxx
Microcontrollers NEC: uPD7xxx series
Microcontrollers Philips (NXP): LPC1xxx, LPC2xxx, LPCxx series, 89xxx series
Microcontrollers Renesas: R8C/Tiny series
Microcontrollers Realtek, M-Square
Microcontrollers Scenix (Ubicom): SXxxx series
Microcontrollers STM: ST7xxx, STR7xx, STR9xx, STM32Fxx, STM8A/S/L series
Microcontrollers Silicon Laboratories(Cygnal): C8051 series
Microcontrollers & Programmable System Memory STMicroelectronics: uPSD, PSD series
Microcontrollers TI: MSP430 (both JTAG and BSL series), MSC12xxx series
Microcontrollers ZILOG: Z8Fxxxx, Z8FMCxxxxx, Z16Fxxxx series, ZLF645x0xx
Various PLD (also by Jam/VME/SVF/STAPL/... Player/JTAG support):
 Altera: MAX 3000A, MAX 7000A, MAX 7000B, MAX 7000S, MAX 9000, MAX II/G/Z
 Xilinx: XC9500, XC9500XL, XC9500XV, CoolRunner XPLA3, CoolRunner-II
PLD Lattice: ispGAL22xV10x, ispLSI1xxxEA, ispLSI2xxxE, ispLSI2xxxV, ispLSI2xxxVE, ispLSI2xxxVL, M4-xx/xx, M4LV-xx/xx, M4A3-xx/xx, M4A5-xx/xx, LC4xxxB/C/V/ZC/ZE, ispCLOCK, Power Manager/II, ProcessorPM
FPGA: Actel: ProASIC3, IGLOO, Fusion
FPGA: Lattice: MachXO, LatticeXP, ispXPGA
Notes: for all supported devices see actual DEVICE LIST
 


Package support
 support all devices in DIP with default socket
package support includes DIP, SDIP, PLCC, JLCC, SOIC, SOP, PSOP, SSOP, TSOP, TSOPII, TSSOP, QFP, PQFP, TQFP, VQFP, QFN (MLF), SON, BGA, EBGA, FBGA, VFBGA, UBGA, FTBGA, LAP, CSP, SCSP etc.
support devices in non-DIP packages up to 48 pins with universal adapters
programmer is compatible with third-party adapters for non-DIP support





Mais fotos

Foto ilustrativa

BeeHive204

Downloads:

BeeHive204

Vídeo do Produto:

Não há Vídeo para este produto.

« VoltarProdutos Relacionados

Atendimento

Telefone de Atendimento
Telefone de Atendimento
macsym@macsym.com.br
Minhas compras (0) »

Busca

Formas de Pagamento
Formas de Entrega
Brasil / Português
2nd © Macsym Tecnologia - Rua Egidio Coni, 5 - Penha - São Paulo - SP - 03654-130 - Brasil